Order cooling vest ice packs by the approved vest model and insert revision. Start with a sample from the kit you already sell, then confirm which pockets the replacement must fit, how the insert is prepared, and how many pieces make a complete refill set. A pack can slide into a pocket and still be the wrong spare if it moves when worn, requires a different preparation method, or leaves the customer short of a complete set.
This guide is for safety distributors and OEM brands replenishing removable inserts for an existing product line. Use the order card below when the carrier stays in the catalog and the packs need a separate SKU.
On this page
Identify the insert before comparing quotes
Start with a previously approved filled insert, its drawing revision if available, and one vest from the affected stock. Record the carrier SKU, vest size range, pocket location and attachment method. If front and back inserts differ, map them separately. Ask the supplier to identify the exact replacement on the quote and to flag any proposed difference in outline, filled thickness, seam position or attachment.
Measure the widest part of the prepared insert and its filled thickness, then check the pocket opening and closure on the assembled vest. A flat drawing misses bulges near the seal and the space needed to slide the pack in. Ask for the approved drawing or a labeled physical sample when the replacement differs from the original. Match the carrier and inserts together before ordering a large batch.
For a Cryozin project, the round-neck zip vest with mesh lining is an example of a garment where the insert set is specified alongside the carrier. The catalog image is a starting point for identifying the layout. Use the approved configuration to establish what comes with the vest and what can be quoted separately.

Match the fill and preparation instructions
Write the approved fill type and grade on the reorder, alongside the drawing revision. If a buyer changes from a gel pack to a phase change material (PCM) pack, treat the change as a sample review. Confirm the supplier’s preparation instructions and compare the replacement in the intended garment. A nominal PCM transition point identifies the material grade. Surface temperature, preparation time and cooling duration depend on the finished configuration and the conditions in which it is used.
Cryozin can discuss nominal PCM options of 28°C, 18°C, 10°C and 5°C for a custom project. Ask which grades are available for the approved insert design and what preparation method applies. For a new configuration, record the conditions the buyer wants to check and who will approve the sample. If the carrier has integrated cooling cells, ask about a service or replacement route for that garment before ordering loose inserts.
Check the pack family even when the carrier brand is the same. For example, ThermApparel describes five pack formats with different shapes or uses. Treat those distinctions as product-specific and request the approved insert reference for your own carrier. ThermApparel’s cooling pack comparison
Quote the piece, refill set and carton separately
Supplier pack counts can mean different things. Ergodyne, for example, lists its Chill-Its 6220 replacement packs as a two-pack. Polar describes compatibility within its named pack families. Both examples show why a quote should specify the model, pack family and quantity in the sales unit. Ergodyne 6220 replacement packs · Polar pack families
Worked order example. A distributor needs 30 complete spare sets. Each vest uses two front and two back inserts, and the shapes differ. Order 60 front and 60 back inserts, or 30 labeled four-piece refill sets. If the supplier sells front and back replacements in separate two-piece packs, the order needs 30 front two-packs and 30 back two-packs. Ask for pieces per sales unit and units per carton on the same quote. The gray pocketed cooling vest is another catalog reference to use when discussing insert layouts.
On Cryozin’s gray four-pocket vest, both 33 × 15.5 cm and 35 × 15.5 cm inserts fit the same pockets and attach to the internal hook-and-loop fastener. Use the approved filling and length when reordering. Existing customers replenishing the original specification can order from 500 inserts. The minimum for a new customer buying these inserts separately is 1,000 inserts.

Copy this replacement insert order card
Use one line per carrier and approved insert revision. Add an annotated pocket photo or drawing to identify any asymmetric parts.
| Record | What to enter or attach | Approval check |
|---|---|---|
| Carrier identity | Vest SKU ___ / sizes ___ / production revision ___ | List the specific models and stock lots covered. |
| Insert identity | Position ___ / drawing revision ___ / fill and grade ___ | Match to a physical approved insert when possible. |
| Loaded fit | Prepared width ___ / length ___ / thickness ___ / attachment ___ | Insert, secure and remove the pack in the approved vest. |
| Complete refill set | Front pieces ___ / back pieces ___ / other ___ | Verify that one refill set fills every designated pocket. |
| Packaging and order | Sets ___ / pieces per pack ___ / packs per carton ___ / label ID ___ | Check that picking staff can distinguish revisions without opening the pack. |
Keep old and new revisions easy to pick
If a new insert has a different shape, grade or fastening, ask the supplier to show which earlier carriers it has been checked against. Record compatibility only after a fit and preparation review on the affected carriers. For versions that have to coexist, assign distinct refill SKUs and mark the supported model or revision on the inner pack and carton. Keep the signed sample and its drawing with the purchasing record so a later reorder has a usable reference.
Before receiving the first replenishment, have someone outside the development team pick one refill set from the label alone, fit it to the intended vest and check the piece count. Fix any ambiguous carton or inner-pack label before it reaches customer service.
Questions buyers ask before reordering
Can the same replacement pack fit two vest models?
Check the pocket geometry, attachment and filled shape on both approved carriers. Record the supported models after the sample review. Similar pocket dimensions alone leave the closure and loaded fit unverified.
Can we order a complete spare set without buying a new vest?
Send the original carrier and insert specification and ask for the spares as a separate quotation line. Confirm pack contents and the order minimum for the replacement configuration.
What if the original drawing is unavailable?
Start with a marked sample vest and a correctly matched insert. Ask the supplier to identify the observed structure, prepare an approval drawing and confirm the fit with you before the replenishment order.
Request a quote for a matched replacement set
Browse Cryozin’s PCM cooling vest formats or consult the loaded fit and module layout guide if the carrier is still being selected. For an existing program, send the carrier model, insert photo or drawing, required sets and carton labeling. Cryozin can review the configuration and confirm a sample or quote route for the matched parts.

