Contact

Product Details

Full-Head Hot Cold Gel Cap with Lower Face Opening for Private Label

This black pull-on cooling cap has fixed solid gel throughout the cap body and Lycra fabric on both sides. It comes in one size and weighs approximately 300–350 g (10.6–12.3 oz) per cap. Confirm the fit on a physical sample.

For private-label sourcing, share your target quantity and retail packaging brief for this full-head hot cold gel cap with lower face opening. Branding, labeling and final configuration are confirmed for the project.

Solid-Gel Cap with a Lower Face Opening

This black pull-on cooling cap has fixed solid gel throughout the cap body and Lycra fabric on both sides. It comes in one size and weighs approximately 300–350 g (10.6–12.3 oz) per cap. Confirm the fit on a physical sample.

The lower face opening is part of the pull-on design. Check where the cap sits and how the opening lines up on a sample for your intended users.

Visible format and project confirmation points

FormatPull-on full-head gel-cap format with lower central face opening
Displayed colorBlack sample shown; standard and project colors to be confirmed
Gel coverageFixed solid gel throughout the cap body.
Fit rangeOne size. Confirm the fit by trying on a sample.
ConstructionLycra fabric inside and outside, with fixed solid gel. Finished net weight is approximately 300–350 g per cap.
Use modeCold or gentle-warm routine following approved exact-product instructions
ArtworkNeutral standard artwork or project artwork to be approved on the real sample
Packaging and documentsConfirmed for the final configuration, channel and destination market

Why the Coverage Map and Face Opening Need Approval

A full-head label does not define where gel panels begin and end. The drawing should show the front, side, crown and rear zones, panel boundaries, seam positions and any areas without filling. The lower opening should be measured at rest and under the intended fit condition.

Buyers should also evaluate visibility, nose clearance, edge position and loaded thickness on representative samples. These checks define the product more accurately than a universal-fit or percentage-coverage slogan.

Sample Checklist for the Complete Cap

  1. Confirm geometry: approve cap height and width, lower opening dimensions, edge shape, panel map and seam locations.
  2. Review fit range: record the intended head-size range and assess opening alignment and edge position on representative samples.
  3. Inspect the internal layout: verify panel placement, fill distribution, thickness, weight balance and seam appearance.
  4. Evaluate the prepared sample: check handling, panel movement, surface condition and fit using only the proposed approved preparation routine.
  5. Approve artwork and labels: verify neutral product wording, logo position, instructions, warnings and destination-market language.
  6. Approve pack-out: confirm pieces per set, pouch or box, instructions, barcode, product protection and carton configuration.

Artwork and Intended-Use Review

Product artwork, the page title, image text, alt text, instructions and retail packaging should use the same approved identity. Condition-specific or outcome wording must not be carried forward from the current images without applicable exact-product evidence and documented human compliance approval.

Share the destination market, sales channel, intended routine, target fit range, neutral artwork and packaging brief through Cryozin’s customization process. Final feasibility and instructions remain subject to sample and specification approval.

Quality and Documentation Scope

The approved sample and specification should become the product reference. Depending on the agreed construction, project controls may include cap and opening dimensions, panel position, fill distribution, seam appearance and integrity, surface condition, artwork, component count, labels and pack-out.

Cryozin’s quality-control process explains how project-specific checkpoints can be defined. The material-selection guide is a general buyer resource and does not establish SKU 971’s fabric, filling, performance or safety properties. Documentation and testing scope must match the final construction and destination market.

Full-Head Cap or Smaller Targeted Mask?

Selection pointFull-head cap formatSmaller mask format
Physical formatPull-on cap surrounding multiple head zonesSmaller product positioned over a limited face or eye area
Key drawing decisionPanel map, lower opening and fit rangeMask outline, eye opening, strap and contact side
Sample focusWeight distribution, opening alignment and coverage boundariesLocalized fit, strap adjustment and edge position
PackagingLarger folded cap and instruction setMore compact mask presentation

Choose by required physical coverage, fit method and pack format. Do not select either format on the basis of an unsupported outcome promise.

Prepare a Cap Development Brief

Provide the destination market, sales channel, intended routine, cap and opening dimensions, target fit range, panel/coverage concept, neutral artwork, packaging files and testing or labeling requirements. Review the cold-compress cap category and Cryozin company information for additional sourcing context.

Product FAQs

How should a full-head cap fit sample be specified?

Provide the head-size range and required front, side, crown and rear coverage. Check the lower-face opening, panel boundaries and edge placement on representative samples.

How do I check the fit?

The cap comes in one size. Share the head circumferences you want to serve and check the sample fit before ordering.

Can preparation instructions be copied from another cap?

Use instructions approved for this cap’s actual fabric, laminate, filling and panel construction. Review preparation, handling, care and storage together with the sample.

What is needed for private-label packaging?

Send the artwork, intended use, market and pack contents. Approve the drawing, contact layers, labeling and any proposed claims for the final construction.

What are the MOQ and sample lead time?

MOQ is assessed per product model. Confirm the applicable quantity for the selected dimensions and configuration in the quotation. Samples take 3–7 business days; regular production takes 18–25 business days. Custom projects can take longer, with timing confirmed individually.

Buyer resources for this product type

Use these guides to define specifications, samples and approval criteria before requesting a production quotation.

Full Name
Please include dimensions, material or format, logo or packaging needs, target market, and required delivery timing.
Approximate units; leave blank if not yet confirmed.
Scroll to Top
Full Name
Please include dimensions, material or format, logo or packaging needs, target market, and required delivery timing.
Approximate units; leave blank if not yet confirmed.